#ifndef HD44780_SETTINGS_H
#define HD44780_SETTINGS_H

//#define F_CPU                    8000000     // Set Clock Frequency

#define EINSYBOARD

#define USE_ADELAY_LIBRARY       0           // Set to 1 to use my ADELAY library, 0 to use internal delay functions
#define LCD_BITS                 4           // 4 for 4 Bit I/O Mode, 8 for 8 Bit I/O Mode
#define RW_LINE_IMPLEMENTED      0           // 0 for no RW line (RW on LCD tied to ground), 1 for RW line present
#define WAIT_MODE                0           // 0=Use Delay Method (Faster if running <10Mhz)
// 1=Use Check Busy Flag (Faster if running >10Mhz) ***Requires RW Line***
#define DELAY_RESET              15          // in mS

#if (LCD_BITS==8)                            // If using 8 bit mode, you must configure DB0-DB7
#define LCD_DB0_PORT           PORTC
#define LCD_DB0_PIN            0
#define LCD_DB1_PORT           PORTC
#define LCD_DB1_PIN            1
#define LCD_DB2_PORT           PORTC
#define LCD_DB2_PIN            2
#define LCD_DB3_PORT           PORTC
#define LCD_DB3_PIN            3
#endif


#ifdef EINSYBOARD
#define LCD_DB4_PORT             PORTF       // If using 4 bit mode, yo umust configure DB4-DB7
#define LCD_DB4_PIN              PF5
#else
#define LCD_DB4_PORT             PORTD       // If using 4 bit mode, yo umust configure DB4-DB7
#define LCD_DB4_PIN              PB2
#endif



#define LCD_DB5_PORT             PORTG
#define LCD_DB5_PIN              PG4
#define LCD_DB6_PORT             PORTH
#define LCD_DB6_PIN              PK7
#define LCD_DB7_PORT             PORTG
#define LCD_DB7_PIN              PA3

#define LCD_RS_PORT              PORTD       // Port for RS line
#define LCD_RS_PIN               PK5           // Pin for RS line

#define LCD_RW_PORT              PORTC       // Port for RW line (ONLY used if RW_LINE_IMPLEMENTED=1)
#define LCD_RW_PIN               PC6           // Pin for RW line (ONLY used if RW_LINE_IMPLEMENTED=1)


#define LCD_DISPLAYS             1           // Up to 4 LCD displays can be used at one time
// All pins are shared between displays except for the E
// pin which each display will have its own

// Display 1 Settings - if you only have 1 display, YOU MUST SET THESE
#define LCD_DISPLAY_LINES        2           // Number of Lines, Only Used for Set I/O Mode Command
#ifdef EINSYBOARD
#define LCD_E_PORT               PORTF       // Port for E line
#define LCD_E_PIN                PF7            // Pin for E line
#else
#define LCD_E_PORT               PORTD       // Port for E line
#define LCD_E_PIN                PD3            // Pin for E line
#endif

#if (LCD_DISPLAYS>=2)                        // If you have 2 displays, set these and change LCD_DISPLAYS=2
#define LCD_DISPLAY2_LINES     2           // Number of Lines, Only Used for Set I/O Mode Command
#define LCD_E2_PORT            PORTC       // Port for E line
#define LCD_E2_PIN             5           // Pin for E line
#endif

#if (LCD_DISPLAYS>=3)                        // If you have 3 displays, set these and change LCD_DISPLAYS=3
#define LCD_DISPLAY3_LINES     2           // Number of Lines, Only Used for Set I/O Mode Command
#define LCD_E3_PORT            PORTC       // Port for E line
#define LCD_E3_PIN             5           // Pin for E line
#endif

#if (LCD_DISPLAYS>=4)                        // If you have 4 displays, set these and change LCD_DISPLAYS=4
#define LCD_DISPLAY4_LINES     2           // Number of Lines, Only Used for Set I/O Mode Command
#define LCD_E4_PORT            PORTC       // Port for E line
#define LCD_E4_PIN             5           // Pin for E line
#endif

#endif