1563 lines
42 KiB
C
1563 lines
42 KiB
C
/*****************************************************************************
|
|
Title: STK500v2 compatible bootloader
|
|
Modified for Wiring board ATMega128-16MHz
|
|
Author: Peter Fleury <pfleury@gmx.ch> http://jump.to/fleury
|
|
Compiler: avr-gcc 3.4.5 or 4.1 / avr-libc 1.4.3
|
|
Hardware: All AVRs with bootloader support, tested with ATmega8
|
|
License: GNU General Public License
|
|
|
|
Modified: Worapoht Kornkaewwattanakul <dev@avride.com> http://www.avride.com
|
|
Date: 17 October 2007
|
|
Update: 1st, 29 Dec 2007 : Enable CMD_SPI_MULTI but ignore unused command by return 0x00 byte response..
|
|
Compiler: WINAVR20060421
|
|
Description: add timeout feature like previous Wiring bootloader
|
|
|
|
DESCRIPTION:
|
|
This program allows an AVR with bootloader capabilities to
|
|
read/write its own Flash/EEprom. To enter Programming mode
|
|
an input pin is checked. If this pin is pulled low, programming mode
|
|
is entered. If not, normal execution is done from $0000
|
|
"reset" vector in Application area.
|
|
Size fits into a 1024 word bootloader section
|
|
when compiled with avr-gcc 4.1
|
|
(direct replace on Wiring Board without fuse setting changed)
|
|
|
|
USAGE:
|
|
- Set AVR MCU type and clock-frequency (F_CPU) in the Makefile.
|
|
- Set baud rate below (AVRISP only works with 115200 bps)
|
|
- compile/link the bootloader with the supplied Makefile
|
|
- program the "Boot Flash section size" (BOOTSZ fuses),
|
|
for boot-size 1024 words: program BOOTSZ01
|
|
- enable the BOOT Reset Vector (program BOOTRST)
|
|
- Upload the hex file to the AVR using any ISP programmer
|
|
- Program Boot Lock Mode 3 (program BootLock 11 and BootLock 12 lock bits) // (leave them)
|
|
- Reset your AVR while keeping PROG_PIN pulled low // (for enter bootloader by switch)
|
|
- Start AVRISP Programmer (AVRStudio/Tools/Program AVR)
|
|
- AVRISP will detect the bootloader
|
|
- Program your application FLASH file and optional EEPROM file using AVRISP
|
|
|
|
Note:
|
|
Erasing the device without flashing, through AVRISP GUI button "Erase Device"
|
|
is not implemented, due to AVRStudio limitations.
|
|
Flash is always erased before programming.
|
|
|
|
AVRdude:
|
|
Please uncomment #define REMOVE_CMD_SPI_MULTI when using AVRdude.
|
|
Comment #define REMOVE_PROGRAM_LOCK_BIT_SUPPORT to reduce code size
|
|
Read Fuse Bits and Read/Write Lock Bits is not supported
|
|
|
|
NOTES:
|
|
Based on Atmel Application Note AVR109 - Self-programming
|
|
Based on Atmel Application Note AVR068 - STK500v2 Protocol
|
|
|
|
LICENSE:
|
|
Copyright (C) 2006 Peter Fleury
|
|
|
|
This program is free software; you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation; either version 2 of the License, or
|
|
any later version.
|
|
|
|
This program is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
*****************************************************************************/
|
|
|
|
//************************************************************************
|
|
//* Edit History
|
|
//************************************************************************
|
|
//* Jul 7, 2010 <MLS> = Mark Sproul msproul@skycharoit.com
|
|
//* Jul 7, 2010 <MLS> Working on mega2560. No Auto-restart
|
|
//* Jul 7, 2010 <MLS> Switched to 8K bytes (4K words) so that we have room for the monitor
|
|
//* Jul 8, 2010 <MLS> Found older version of source that had auto restart, put that code back in
|
|
//* Jul 8, 2010 <MLS> Adding monitor code
|
|
//* Jul 11, 2010 <MLS> Added blinking LED while waiting for download to start
|
|
//* Jul 11, 2010 <MLS> Added EEPROM test
|
|
//* Jul 29, 2010 <MLS> Added recchar_timeout for timing out on bootloading
|
|
//* Aug 23, 2010 <MLS> Added support for atmega2561
|
|
//* Aug 26, 2010 <MLS> Removed support for BOOT_BY_SWITCH
|
|
//* Sep 8, 2010 <MLS> Added support for atmega16
|
|
//* Nov 9, 2010 <MLS> Issue 392:Fixed bug that 3 !!! in code would cause it to jump to monitor
|
|
//* Jun 24, 2011 <MLS> Removed analogRead (was not used)
|
|
//* Dec 29, 2011 <MLS> Issue 181: added watch dog timmer support
|
|
//* Dec 29, 2011 <MLS> Issue 505: bootloader is comparing the seqNum to 1 or the current sequence
|
|
//* Jan 1, 2012 <MLS> Issue 543: CMD_CHIP_ERASE_ISP now returns STATUS_CMD_FAILED instead of STATUS_CMD_OK
|
|
//* Jan 1, 2012 <MLS> Issue 543: Write EEPROM now does something (NOT TESTED)
|
|
//* Jan 1, 2012 <MLS> Issue 544: stk500v2 bootloader doesn't support reading fuses
|
|
//************************************************************************
|
|
|
|
//************************************************************************
|
|
//* these are used to test issues
|
|
//* http://code.google.com/p/arduino/issues/detail?id=505
|
|
//* Reported by mark.stubbs, Mar 14, 2011
|
|
//* The STK500V2 bootloader is comparing the seqNum to 1 or the current sequence
|
|
//* (IE: Requiring the sequence to be 1 or match seqNum before continuing).
|
|
//* The correct behavior is for the STK500V2 to accept the PC's sequence number, and echo it back for the reply message.
|
|
#define _FIX_ISSUE_505_
|
|
//************************************************************************
|
|
//* Issue 181: added watch dog timmer support
|
|
#define _FIX_ISSUE_181_
|
|
// LCD startup screen and boot animation
|
|
#define LCD_HD44780
|
|
#define LCD_HD44780_ANIMATION
|
|
#define LCD_HD44780_COUNTER
|
|
// Dual serial support
|
|
#define DUALSERIAL
|
|
// EINSY board
|
|
#define EINSYBOARD
|
|
|
|
|
|
#include <inttypes.h>
|
|
#include <avr/io.h>
|
|
#include <avr/interrupt.h>
|
|
#include <avr/boot.h>
|
|
#include <avr/pgmspace.h>
|
|
#include <util/delay.h>
|
|
#include <avr/eeprom.h>
|
|
#include <avr/common.h>
|
|
#include "command.h"
|
|
|
|
#ifdef LCD_HD44780
|
|
#include "lcd.h"
|
|
#endif
|
|
|
|
|
|
#ifndef EEWE
|
|
#define EEWE 1
|
|
#endif
|
|
#ifndef EEMWE
|
|
#define EEMWE 2
|
|
#endif
|
|
|
|
|
|
|
|
/*
|
|
* Uncomment the following lines to save code space
|
|
*/
|
|
//#define REMOVE_PROGRAM_LOCK_BIT_SUPPORT // disable program lock bits
|
|
//#define REMOVE_BOOTLOADER_LED // no LED to show active bootloader
|
|
//#define REMOVE_CMD_SPI_MULTI // disable processing of SPI_MULTI commands, Remark this line for AVRDUDE <Worapoht>
|
|
//
|
|
|
|
|
|
|
|
//************************************************************************
|
|
//* LED on pin "PROGLED_PIN" on port "PROGLED_PORT"
|
|
//* indicates that bootloader is active
|
|
//* PG2 -> LED on Wiring board
|
|
//************************************************************************
|
|
#define BLINK_LED_WHILE_WAITING
|
|
|
|
#ifdef _MEGA_BOARD_
|
|
#define PROGLED_PORT PORTB
|
|
#define PROGLED_DDR DDRB
|
|
#define PROGLED_PIN PINB7
|
|
#elif defined( _BOARD_AMBER128_ )
|
|
//* this is for the amber 128 http://www.soc-robotics.com/
|
|
//* onbarod led is PORTE4
|
|
#define PROGLED_PORT PORTD
|
|
#define PROGLED_DDR DDRD
|
|
#define PROGLED_PIN PINE7
|
|
#elif defined( _CEREBOTPLUS_BOARD_ ) || defined(_CEREBOT_II_BOARD_)
|
|
//* this is for the Cerebot 2560 board and the Cerebot-ii
|
|
//* onbarod leds are on PORTE4-7
|
|
#define PROGLED_PORT PORTE
|
|
#define PROGLED_DDR DDRE
|
|
#define PROGLED_PIN PINE7
|
|
#elif defined( _PENGUINO_ )
|
|
//* this is for the Penguino
|
|
//* onbarod led is PORTE4
|
|
#define PROGLED_PORT PORTC
|
|
#define PROGLED_DDR DDRC
|
|
#define PROGLED_PIN PINC6
|
|
#elif defined( _ANDROID_2561_ ) || defined( __AVR_ATmega2561__ )
|
|
//* this is for the Boston Android 2561
|
|
//* onbarod led is PORTE4
|
|
#define PROGLED_PORT PORTA
|
|
#define PROGLED_DDR DDRA
|
|
#define PROGLED_PIN PINA3
|
|
#elif defined( _BOARD_MEGA16 )
|
|
//* onbarod led is PORTA7
|
|
#define PROGLED_PORT PORTA
|
|
#define PROGLED_DDR DDRA
|
|
#define PROGLED_PIN PINA7
|
|
#define UART_BAUDRATE_DOUBLE_SPEED 0
|
|
|
|
#elif defined( _BOARD_BAHBOT_ )
|
|
//* dosent have an onboard LED but this is what will probably be added to this port
|
|
#define PROGLED_PORT PORTB
|
|
#define PROGLED_DDR DDRB
|
|
#define PROGLED_PIN PINB0
|
|
|
|
#elif defined( _BOARD_ROBOTX_ )
|
|
#define PROGLED_PORT PORTB
|
|
#define PROGLED_DDR DDRB
|
|
#define PROGLED_PIN PINB6
|
|
#elif defined( _BOARD_CUSTOM1284_BLINK_B0_ )
|
|
#define PROGLED_PORT PORTB
|
|
#define PROGLED_DDR DDRB
|
|
#define PROGLED_PIN PINB0
|
|
#elif defined( _BOARD_CUSTOM1284_ )
|
|
#define PROGLED_PORT PORTD
|
|
#define PROGLED_DDR DDRD
|
|
#define PROGLED_PIN PIND5
|
|
#elif defined( _AVRLIP_ )
|
|
#define PROGLED_PORT PORTB
|
|
#define PROGLED_DDR DDRB
|
|
#define PROGLED_PIN PINB5
|
|
#elif defined( _BOARD_STK500_ )
|
|
#define PROGLED_PORT PORTA
|
|
#define PROGLED_DDR DDRA
|
|
#define PROGLED_PIN PINA7
|
|
#elif defined( _BOARD_STK502_ )
|
|
#define PROGLED_PORT PORTB
|
|
#define PROGLED_DDR DDRB
|
|
#define PROGLED_PIN PINB5
|
|
#elif defined( _BOARD_STK525_ )
|
|
#define PROGLED_PORT PORTB
|
|
#define PROGLED_DDR DDRB
|
|
#define PROGLED_PIN PINB7
|
|
#else
|
|
#define PROGLED_PORT PORTG
|
|
#define PROGLED_DDR DDRG
|
|
#define PROGLED_PIN PING2
|
|
#endif
|
|
|
|
|
|
|
|
/*
|
|
* define CPU frequency in Mhz here if not defined in Makefile
|
|
*/
|
|
#ifndef F_CPU
|
|
#define F_CPU 16000000UL
|
|
#endif
|
|
|
|
#define _BLINK_LOOP_COUNT_ (F_CPU / 2250)
|
|
/*
|
|
* UART Baudrate, AVRStudio AVRISP only accepts 115200 bps
|
|
*/
|
|
|
|
#ifndef BAUDRATE
|
|
#define BAUDRATE 115200
|
|
#endif
|
|
|
|
/*
|
|
* Enable (1) or disable (0) USART double speed operation
|
|
*/
|
|
#ifndef UART_BAUDRATE_DOUBLE_SPEED
|
|
#if defined (__AVR_ATmega32__)
|
|
#define UART_BAUDRATE_DOUBLE_SPEED 0
|
|
#else
|
|
#define UART_BAUDRATE_DOUBLE_SPEED 1
|
|
#endif
|
|
#endif
|
|
|
|
/*
|
|
* HW and SW version, reported to AVRISP, must match version of AVRStudio
|
|
*/
|
|
#define CONFIG_PARAM_BUILD_NUMBER_LOW 0
|
|
#define CONFIG_PARAM_BUILD_NUMBER_HIGH 0
|
|
#define CONFIG_PARAM_HW_VER 0x0F
|
|
#define CONFIG_PARAM_SW_MAJOR 2
|
|
#define CONFIG_PARAM_SW_MINOR 0x0A
|
|
|
|
/*
|
|
* Calculate the address where the bootloader starts from FLASHEND and BOOTSIZE
|
|
* (adjust BOOTSIZE below and BOOTLOADER_ADDRESS in Makefile if you want to change the size of the bootloader)
|
|
*/
|
|
//#define BOOTSIZE 1024
|
|
#if FLASHEND > 0x0F000
|
|
#define BOOTSIZE 8192
|
|
#else
|
|
#define BOOTSIZE 2048
|
|
#endif
|
|
|
|
//#define APP_END (FLASHEND -(2*BOOTSIZE) + 1)
|
|
#define APP_END (FLASHEND -(BOOTSIZE) + 1)
|
|
|
|
/*
|
|
* Signature bytes are not available in avr-gcc io_xxx.h
|
|
*/
|
|
#if defined (__AVR_ATmega8__)
|
|
#define SIGNATURE_BYTES 0x1E9307
|
|
#elif defined (__AVR_ATmega16__)
|
|
#define SIGNATURE_BYTES 0x1E9403
|
|
#elif defined (__AVR_ATmega32__)
|
|
#define SIGNATURE_BYTES 0x1E9502
|
|
#elif defined (__AVR_ATmega8515__)
|
|
#define SIGNATURE_BYTES 0x1E9306
|
|
#elif defined (__AVR_ATmega8535__)
|
|
#define SIGNATURE_BYTES 0x1E9308
|
|
#elif defined (__AVR_ATmega162__)
|
|
#define SIGNATURE_BYTES 0x1E9404
|
|
#elif defined (__AVR_ATmega128__)
|
|
#define SIGNATURE_BYTES 0x1E9702
|
|
#elif defined (__AVR_ATmega1280__)
|
|
#define SIGNATURE_BYTES 0x1E9703
|
|
#elif defined (__AVR_ATmega2560__)
|
|
#define SIGNATURE_BYTES 0x1E9801
|
|
#elif defined (__AVR_ATmega2561__)
|
|
#define SIGNATURE_BYTES 0x1e9802
|
|
#elif defined (__AVR_ATmega1284P__)
|
|
#define SIGNATURE_BYTES 0x1e9705
|
|
#elif defined (__AVR_ATmega640__)
|
|
#define SIGNATURE_BYTES 0x1e9608
|
|
#elif defined (__AVR_ATmega64__)
|
|
#define SIGNATURE_BYTES 0x1E9602
|
|
#elif defined (__AVR_ATmega169__)
|
|
#define SIGNATURE_BYTES 0x1e9405
|
|
#elif defined (__AVR_AT90USB1287__)
|
|
#define SIGNATURE_BYTES 0x1e9782
|
|
#else
|
|
#error "no signature definition for MCU available"
|
|
#endif
|
|
|
|
|
|
#if defined(_BOARD_ROBOTX_) || defined(__AVR_AT90USB1287__) || defined(__AVR_AT90USB1286__)
|
|
#define UART_BAUD_RATE_LOW UBRR1L
|
|
#define UART_STATUS_REG UCSR1A
|
|
#define UART_CONTROL_REG UCSR1B
|
|
#define UART_ENABLE_TRANSMITTER TXEN1
|
|
#define UART_ENABLE_RECEIVER RXEN1
|
|
#define UART_TRANSMIT_COMPLETE TXC1
|
|
#define UART_RECEIVE_COMPLETE RXC1
|
|
#define UART_DATA_REG UDR1
|
|
#define UART_DOUBLE_SPEED U2X1
|
|
|
|
#elif defined(__AVR_ATmega8__) || defined(__AVR_ATmega16__) || defined(__AVR_ATmega32__) \
|
|
|| defined(__AVR_ATmega8515__) || defined(__AVR_ATmega8535__)
|
|
/* ATMega8 with one USART */
|
|
#define UART_BAUD_RATE_LOW UBRRL
|
|
#define UART_STATUS_REG UCSRA
|
|
#define UART_CONTROL_REG UCSRB
|
|
#define UART_ENABLE_TRANSMITTER TXEN
|
|
#define UART_ENABLE_RECEIVER RXEN
|
|
#define UART_TRANSMIT_COMPLETE TXC
|
|
#define UART_RECEIVE_COMPLETE RXC
|
|
#define UART_DATA_REG UDR
|
|
#define UART_DOUBLE_SPEED U2X
|
|
|
|
#elif defined(__AVR_ATmega64__) || defined(__AVR_ATmega128__) || defined(__AVR_ATmega162__) \
|
|
|| defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__) || defined(__AVR_ATmega2561__)
|
|
/* ATMega with two USART, use UART0 */
|
|
#define UART_BAUD_RATE_LOW UBRR0L
|
|
#define UART_STATUS_REG UCSR0A
|
|
#define UART_CONTROL_REG UCSR0B
|
|
#define UART_ENABLE_TRANSMITTER TXEN0
|
|
#define UART_ENABLE_RECEIVER RXEN0
|
|
#define UART_TRANSMIT_COMPLETE TXC0
|
|
#define UART_RECEIVE_COMPLETE RXC0
|
|
#define UART_DATA_REG UDR0
|
|
#define UART_DOUBLE_SPEED U2X0
|
|
#elif defined(UBRR0L) && defined(UCSR0A) && defined(TXEN0)
|
|
/* ATMega with two USART, use UART0 */
|
|
#define UART_BAUD_RATE_LOW UBRR0L
|
|
#define UART_STATUS_REG UCSR0A
|
|
#define UART_CONTROL_REG UCSR0B
|
|
#define UART_ENABLE_TRANSMITTER TXEN0
|
|
#define UART_ENABLE_RECEIVER RXEN0
|
|
#define UART_TRANSMIT_COMPLETE TXC0
|
|
#define UART_RECEIVE_COMPLETE RXC0
|
|
#define UART_DATA_REG UDR0
|
|
#define UART_DOUBLE_SPEED U2X0
|
|
#elif defined(UBRRL) && defined(UCSRA) && defined(UCSRB) && defined(TXEN) && defined(RXEN)
|
|
//* catch all
|
|
#define UART_BAUD_RATE_LOW UBRRL
|
|
#define UART_STATUS_REG UCSRA
|
|
#define UART_CONTROL_REG UCSRB
|
|
#define UART_ENABLE_TRANSMITTER TXEN
|
|
#define UART_ENABLE_RECEIVER RXEN
|
|
#define UART_TRANSMIT_COMPLETE TXC
|
|
#define UART_RECEIVE_COMPLETE RXC
|
|
#define UART_DATA_REG UDR
|
|
#define UART_DOUBLE_SPEED U2X
|
|
#else
|
|
#error "no UART definition for MCU available"
|
|
#endif
|
|
|
|
|
|
/*
|
|
* Macro to calculate UBBR from XTAL and baudrate
|
|
*/
|
|
#if defined(__AVR_ATmega32__) && UART_BAUDRATE_DOUBLE_SPEED
|
|
#define UART_BAUD_SELECT(baudRate,xtalCpu) ((xtalCpu / 4 / baudRate - 1) / 2)
|
|
#elif defined(__AVR_ATmega32__)
|
|
#define UART_BAUD_SELECT(baudRate,xtalCpu) ((xtalCpu / 8 / baudRate - 1) / 2)
|
|
#elif UART_BAUDRATE_DOUBLE_SPEED
|
|
#define UART_BAUD_SELECT(baudRate,xtalCpu) (((float)(xtalCpu))/(((float)(baudRate))*8.0)-1.0+0.5)
|
|
#else
|
|
#define UART_BAUD_SELECT(baudRate,xtalCpu) (((float)(xtalCpu))/(((float)(baudRate))*16.0)-1.0+0.5)
|
|
#endif
|
|
|
|
#ifdef DUALSERIAL
|
|
|
|
// UART defines
|
|
#define UART_BAUD_RATE_LOW0 UBRR0L
|
|
#define UART_STATUS_REG0 UCSR0A
|
|
#define UART_CONTROL_REG0 UCSR0B
|
|
#define UART_ENABLE_TRANSMITTER0 TXEN0
|
|
#define UART_ENABLE_RECEIVER0 RXEN0
|
|
#define UART_TRANSMIT_COMPLETE0 TXC0
|
|
#define UART_RECEIVE_COMPLETE0 RXC0
|
|
#define UART_DATA_REG0 UDR0
|
|
#define UART_DOUBLE_SPEED0 U2X0
|
|
|
|
#define UART_BAUD_RATE_LOW2 UBRR2L
|
|
#define UART_STATUS_REG2 UCSR2A
|
|
#define UART_CONTROL_REG2 UCSR2B
|
|
#define UART_ENABLE_TRANSMITTER2 TXEN2
|
|
#define UART_ENABLE_RECEIVER2 RXEN2
|
|
#define UART_TRANSMIT_COMPLETE2 TXC2
|
|
#define UART_RECEIVE_COMPLETE2 RXC2
|
|
#define UART_DATA_REG2 UDR2
|
|
#define UART_DOUBLE_SPEED2 U2X2
|
|
|
|
#endif //DUALSERIAL
|
|
|
|
|
|
#define UART_BAUD_SELECT(baudRate,xtalCpu) (((float)(xtalCpu))/(((float)(baudRate))*8.0)-1.0+0.5)
|
|
|
|
/*
|
|
* States used in the receive state machine
|
|
*/
|
|
#define ST_START 0
|
|
#define ST_GET_SEQ_NUM 1
|
|
#define ST_MSG_SIZE_1 2
|
|
#define ST_MSG_SIZE_2 3
|
|
#define ST_GET_TOKEN 4
|
|
#define ST_GET_DATA 5
|
|
#define ST_GET_CHECK 6
|
|
#define ST_PROCESS 7
|
|
|
|
/*
|
|
* use 16bit address variable for ATmegas with <= 64K flash
|
|
*/
|
|
#if defined(RAMPZ)
|
|
typedef uint32_t address_t;
|
|
#else
|
|
typedef uint16_t address_t;
|
|
#endif
|
|
|
|
/*
|
|
* function prototypes
|
|
*/
|
|
static void sendchar(char c);
|
|
//static unsigned char recchar(void);
|
|
|
|
#ifdef DUALSERIAL
|
|
int selectedSerial;
|
|
#endif //DUALSERIAL
|
|
|
|
/*
|
|
* since this bootloader is not linked against the avr-gcc crt1 functions,
|
|
* to reduce the code size, we need to provide our own initialization
|
|
*/
|
|
void __jumpMain (void) __attribute__ ((naked)) __attribute__ ((section (".init9")));
|
|
#include <avr/sfr_defs.h>
|
|
|
|
//#define SPH_REG 0x3E
|
|
//#define SPL_REG 0x3D
|
|
|
|
#define STACK_TOP (RAMEND - 16)
|
|
|
|
//*****************************************************************************
|
|
void __jumpMain(void)
|
|
{
|
|
//* July 17, 2010 <MLS> Added stack pointer initialzation
|
|
//* the first line did not do the job on the ATmega128
|
|
|
|
asm volatile ( ".set __stack, %0" :: "i" (STACK_TOP) );
|
|
|
|
//* set stack pointer to top of RAM
|
|
|
|
asm volatile ( "ldi 16, %0" :: "i" (STACK_TOP >> 8) );
|
|
asm volatile ( "out %0,16" :: "i" (AVR_STACK_POINTER_HI_ADDR) );
|
|
|
|
asm volatile ( "ldi 16, %0" :: "i" (STACK_TOP & 0x0ff) );
|
|
asm volatile ( "out %0,16" :: "i" (AVR_STACK_POINTER_LO_ADDR) );
|
|
|
|
asm volatile ( "clr __zero_reg__" ); // GCC depends on register r1 set to 0
|
|
asm volatile ( "out %0, __zero_reg__" :: "I" (_SFR_IO_ADDR(SREG)) ); // set SREG to 0
|
|
asm volatile ( "jmp main"); // jump to main()
|
|
}
|
|
|
|
|
|
//*****************************************************************************
|
|
void delay_ms(unsigned int timedelay)
|
|
{
|
|
unsigned int i;
|
|
for (i=0;i<timedelay;i++)
|
|
{
|
|
_delay_ms(0.5);
|
|
}
|
|
}
|
|
/*
|
|
void lcd_print_hex_nibble(uint8_t val)
|
|
{
|
|
lcd_putc((val > 9)?('A' + val - 10):('0' + val));
|
|
}
|
|
|
|
void lcd_print_hex_byte(uint8_t val)
|
|
{
|
|
lcd_print_hex_nibble(val >> 4);
|
|
lcd_print_hex_nibble(val & 0xf);
|
|
}
|
|
|
|
void lcd_print_hex_word(uint16_t val)
|
|
{
|
|
lcd_print_hex_byte(val >> 8);
|
|
lcd_print_hex_byte(val & 0xff);
|
|
}
|
|
|
|
void lcd_print_hex_dword(uint32_t val)
|
|
{
|
|
lcd_print_hex_word(val >> 16);
|
|
lcd_print_hex_word(val & 0xffff);
|
|
}
|
|
/**/
|
|
/*
|
|
const unsigned long ulFlashEnd = FLASHEND;
|
|
const unsigned long ulRamEnd = RAMEND;
|
|
const unsigned long ulBootSize = BOOTSIZE;
|
|
const unsigned long ulAppEnd = APP_END;
|
|
*/
|
|
//*****************************************************************************
|
|
/*
|
|
* send single byte to USART, wait until transmission is completed
|
|
*/
|
|
static void sendchar(char c)
|
|
{
|
|
#ifdef DUALSERIAL
|
|
if (selectedSerial == 0)
|
|
{
|
|
UART_DATA_REG0 = c; // prepare transmission
|
|
while (!(UART_STATUS_REG0 & (1 << UART_TRANSMIT_COMPLETE0))); // wait until byte sent
|
|
UART_STATUS_REG0 |= (1 << UART_TRANSMIT_COMPLETE0); // delete TXCflag
|
|
}
|
|
else if (selectedSerial == 2)
|
|
{
|
|
UART_DATA_REG2 = c; // prepare transmission
|
|
while (!(UART_STATUS_REG2 & (1 << UART_TRANSMIT_COMPLETE2))); // wait until byte sent
|
|
UART_STATUS_REG2 |= (1 << UART_TRANSMIT_COMPLETE2); // delete TXCflag
|
|
}
|
|
#else //DUALSERIAL
|
|
UART_DATA_REG = c; // prepare transmission
|
|
while (!(UART_STATUS_REG & (1 << UART_TRANSMIT_COMPLETE))); // wait until byte sent
|
|
UART_STATUS_REG |= (1 << UART_TRANSMIT_COMPLETE); // delete TXCflag
|
|
#endif //DUALSERIAL
|
|
}
|
|
|
|
|
|
//************************************************************************
|
|
#ifdef DUALSERIAL
|
|
static int Serial_Available(int serial)
|
|
{
|
|
if (serial == 0)
|
|
return (UART_STATUS_REG0 & (1 << UART_RECEIVE_COMPLETE0)); // wait for data
|
|
else if (serial == 2)
|
|
return (UART_STATUS_REG2 & (1 << UART_RECEIVE_COMPLETE2)); // wait for data
|
|
return 0;
|
|
}
|
|
#else //DUALSERIAL
|
|
static int Serial_Available(void)
|
|
{
|
|
return (UART_STATUS_REG & (1 << UART_RECEIVE_COMPLETE)); // wait for data
|
|
}
|
|
#endif //DUALSERIAL
|
|
|
|
|
|
//*****************************************************************************
|
|
/*
|
|
* Read single byte from USART, block if no data available
|
|
*/
|
|
/*static unsigned char recchar(void)
|
|
{
|
|
#ifdef DUALSERIAL
|
|
if (selectedSerial == 0)
|
|
{
|
|
while (!(UART_STATUS_REG0 & (1 << UART_RECEIVE_COMPLETE0))) { } // wait for data
|
|
return UART_DATA_REG0;
|
|
}
|
|
else if (selectedSerial == 2)
|
|
{
|
|
while (!(UART_STATUS_REG2 & (1 << UART_RECEIVE_COMPLETE2))) { } // wait for data
|
|
return UART_DATA_REG2;
|
|
}
|
|
return 0;
|
|
#else //DUALSERIAL
|
|
while (!(UART_STATUS_REG & (1 << UART_RECEIVE_COMPLETE))) { } // wait for data
|
|
return UART_DATA_REG;
|
|
#endif //DUALSERIAL
|
|
}*/
|
|
|
|
#define MAX_TIME_COUNT (F_CPU >> 1)
|
|
//*****************************************************************************
|
|
static unsigned char recchar_timeout(void)
|
|
{
|
|
uint32_t count = 0;
|
|
#ifdef DUALSERIAL
|
|
while (1)
|
|
{
|
|
if ((selectedSerial == 0) && (UART_STATUS_REG0 & (1 << UART_RECEIVE_COMPLETE0))) break;
|
|
else if ((selectedSerial == 2) && (UART_STATUS_REG2 & (1 << UART_RECEIVE_COMPLETE2))) break;
|
|
count++;
|
|
if (count > MAX_TIME_COUNT)
|
|
{
|
|
unsigned int data;
|
|
#if (FLASHEND > 0x10000)
|
|
data = pgm_read_word_far(0); //* get the first word of the user program
|
|
#else
|
|
data = pgm_read_word_near(0); //* get the first word of the user program
|
|
#endif
|
|
if (data != 0xffff) //* make sure its valid before jumping to it.
|
|
{
|
|
asm volatile(
|
|
"clr r30 \n\t"
|
|
"clr r31 \n\t"
|
|
"ijmp \n\t"
|
|
);
|
|
}
|
|
count = 0;
|
|
}
|
|
}
|
|
if (selectedSerial == 0) return UART_DATA_REG0;
|
|
else if (selectedSerial == 2) return UART_DATA_REG2;
|
|
return 0;
|
|
#else //DUALSERIAL
|
|
while (!(UART_STATUS_REG & (1 << UART_RECEIVE_COMPLETE)))
|
|
{
|
|
// wait for data
|
|
count++;
|
|
if (count > MAX_TIME_COUNT)
|
|
{
|
|
unsigned int data;
|
|
#if (FLASHEND > 0x10000)
|
|
data = pgm_read_word_far(0); //* get the first word of the user program
|
|
#else
|
|
data = pgm_read_word_near(0); //* get the first word of the user program
|
|
#endif
|
|
if (data != 0xffff) //* make sure its valid before jumping to it.
|
|
{
|
|
asm volatile(
|
|
"clr r30 \n\t"
|
|
"clr r31 \n\t"
|
|
"ijmp \n\t"
|
|
);
|
|
}
|
|
count = 0;
|
|
}
|
|
}
|
|
return UART_DATA_REG;
|
|
#endif //DUALSERIAL
|
|
}
|
|
|
|
#ifdef DUALSERIAL
|
|
void initUart()
|
|
{
|
|
// init uart0
|
|
UART_STATUS_REG0 |= (1 <<UART_DOUBLE_SPEED0);
|
|
UART_BAUD_RATE_LOW0 = UART_BAUD_SELECT(BAUDRATE,F_CPU);
|
|
UART_CONTROL_REG0 = (1 << UART_ENABLE_RECEIVER0) | (1 << UART_ENABLE_TRANSMITTER0);
|
|
// init uart2
|
|
UART_STATUS_REG2 |= (1 <<UART_DOUBLE_SPEED2);
|
|
UART_BAUD_RATE_LOW2 = UART_BAUD_SELECT(BAUDRATE,F_CPU);
|
|
UART_CONTROL_REG2 = (1 << UART_ENABLE_RECEIVER2) | (1 << UART_ENABLE_TRANSMITTER2);
|
|
}
|
|
#endif //DUALSERIAL
|
|
|
|
/*void sendHello() {
|
|
sendchar('H');
|
|
sendchar('e');
|
|
sendchar('l');
|
|
sendchar('l');
|
|
sendchar('o');
|
|
sendchar('!');
|
|
sendchar('\n');
|
|
}*/
|
|
|
|
#ifdef EINSYBOARD
|
|
|
|
void blinkBootLed(int state)
|
|
{
|
|
if (state == 1)
|
|
PORTB = 0b10000000;
|
|
else
|
|
PORTB = 0b00000000;
|
|
}
|
|
|
|
//Heaters off (PG5=0, PE5=0)
|
|
//Fans on (PH5=1, PH3=1)
|
|
//Motors off (PA4..7=1)
|
|
void pinsToDefaultState()
|
|
{
|
|
/*
|
|
DDRG = 0b00001000;
|
|
DDRE = 0b00001000;
|
|
DDRH = 0b00101000;
|
|
DDRA = 0b00011110;
|
|
DDRB = 0b10000000;
|
|
PORTH = 0b00101000;
|
|
PORTG = 0b00000000;
|
|
PORTE = 0b00000000;
|
|
PORTA = 0b00000000;*/ //original code
|
|
DDRA |= 0b11110000; //PA4..7 out
|
|
PORTA |= 0b11110000; //PA4..7 = 1
|
|
DDRE |= 0b00100000; //PE5 out
|
|
PORTE &= 0b11011111; //PE5 = 0
|
|
DDRG |= 0b00100000; //PG5 out
|
|
PORTG &= 0b11011111; //PG5 = 0
|
|
DDRH |= 0b00101000; //PH5, PH3 out
|
|
PORTH |= 0b00101000; //PH5, PH3 = 1
|
|
}
|
|
|
|
#endif //EINSYBOARD
|
|
|
|
//* for watch dog timer startup
|
|
//void (*app_start)(void) = 0x0000;
|
|
|
|
unsigned long flashSize = 0; //flash data size in bytes
|
|
unsigned long flashCounter = 0; //flash counter (readed / written bytes)
|
|
address_t flashAddressLast = 0; //last written flash address
|
|
int flashOperation = 0; //current flash operation (0-nothing, 1-write, 2-verify)
|
|
|
|
#define RAMSIZE 0x2000
|
|
#define boot_src_addr (*((uint32_t*)(RAMSIZE - 16)))
|
|
#define boot_dst_addr (*((uint32_t*)(RAMSIZE - 12)))
|
|
#define boot_copy_size (*((uint16_t*)(RAMSIZE - 8)))
|
|
#define boot_reserved (*((uint8_t*)(RAMSIZE - 6)))
|
|
#define boot_app_flags (*((uint8_t*)(RAMSIZE - 5)))
|
|
#define boot_app_magic (*((uint32_t*)(RAMSIZE - 4)))
|
|
#define BOOT_APP_FLG_ERASE 0x01
|
|
#define BOOT_APP_FLG_COPY 0x02
|
|
#define BOOT_APP_FLG_FLASH 0x04
|
|
|
|
|
|
//*****************************************************************************
|
|
int main(void)
|
|
{
|
|
address_t address = 0;
|
|
address_t eraseAddress = 0;
|
|
unsigned char msgParseState;
|
|
unsigned int ii = 0;
|
|
unsigned char checksum = 0;
|
|
unsigned char seqNum = 0;
|
|
unsigned int msgLength = 0;
|
|
unsigned char msgBuffer[285];
|
|
unsigned char c, *p;
|
|
unsigned char isLeave = 0;
|
|
|
|
unsigned long boot_timeout;
|
|
unsigned long boot_timer;
|
|
unsigned int boot_state;
|
|
|
|
//* some chips dont set the stack properly
|
|
// this is already done in __jumpMain
|
|
/* asm volatile ( ".set __stack, %0" :: "i" (RAMEND) );
|
|
asm volatile ( "ldi 16, %0" :: "i" (RAMEND >> 8) );
|
|
asm volatile ( "out %0,16" :: "i" (AVR_STACK_POINTER_HI_ADDR) );
|
|
asm volatile ( "ldi 16, %0" :: "i" (RAMEND & 0x0ff) );
|
|
asm volatile ( "out %0,16" :: "i" (AVR_STACK_POINTER_LO_ADDR) );*/
|
|
|
|
#ifdef _FIX_ISSUE_181_
|
|
//************************************************************************
|
|
//* Dec 29, 2011 <MLS> Issue #181, added watch dog timmer support
|
|
//* handle the watch dog timer
|
|
uint8_t mcuStatusReg;
|
|
mcuStatusReg = MCUSR;
|
|
|
|
__asm__ __volatile__ ("cli");
|
|
__asm__ __volatile__ ("wdr");
|
|
MCUSR = 0;
|
|
WDTCSR |= _BV(WDCE) | _BV(WDE);
|
|
WDTCSR = 0;
|
|
__asm__ __volatile__ ("sei");
|
|
// check if WDT generated the reset, if so, go straight to app
|
|
if (mcuStatusReg & _BV(WDRF))
|
|
{
|
|
if (boot_app_magic == 0x55aa55aa)
|
|
{
|
|
/// uint16_t tmp_boot_copy_size = boot_copy_size;
|
|
/// uint32_t tmp_boot_src_addr = boot_src_addr;
|
|
|
|
address = boot_dst_addr;
|
|
address_t pageAddress = address;
|
|
while (boot_copy_size)
|
|
{
|
|
if (boot_app_flags & BOOT_APP_FLG_ERASE)
|
|
{
|
|
boot_page_erase(pageAddress);
|
|
boot_spm_busy_wait();
|
|
}
|
|
pageAddress += SPM_PAGESIZE;
|
|
if ((boot_app_flags & BOOT_APP_FLG_COPY))
|
|
{
|
|
while (boot_copy_size && (address < pageAddress))
|
|
{
|
|
uint16_t word = 0x0000;
|
|
if (boot_app_flags & BOOT_APP_FLG_FLASH)
|
|
word = pgm_read_word_far(boot_src_addr); //from FLASH
|
|
else
|
|
word = *((uint16_t*)boot_src_addr); //from RAM
|
|
boot_page_fill(address, word);
|
|
address += 2;
|
|
boot_src_addr += 2;
|
|
if (boot_copy_size > 2)
|
|
boot_copy_size -= 2;
|
|
else
|
|
boot_copy_size = 0;
|
|
}
|
|
boot_page_write(pageAddress - SPM_PAGESIZE);
|
|
boot_spm_busy_wait();
|
|
boot_rww_enable();
|
|
}
|
|
else
|
|
{
|
|
address += SPM_PAGESIZE;
|
|
if (boot_copy_size > SPM_PAGESIZE)
|
|
boot_copy_size -= SPM_PAGESIZE;
|
|
else
|
|
boot_copy_size = 0;
|
|
}
|
|
}
|
|
/// boot_copy_size = tmp_boot_copy_size;
|
|
/// boot_src_addr = tmp_boot_src_addr;
|
|
|
|
}
|
|
goto exit;
|
|
// original implementation app_start() does not work
|
|
// app_start();
|
|
}
|
|
//************************************************************************
|
|
#endif
|
|
|
|
|
|
boot_timer = 0;
|
|
boot_state = 0;
|
|
|
|
#ifdef BLINK_LED_WHILE_WAITING
|
|
// boot_timeout = 90000; //* should be about 4 seconds
|
|
// boot_timeout = 170000;
|
|
boot_timeout = 20000; //* should be about 1 second
|
|
#else
|
|
boot_timeout = 3500000; // 7 seconds , approx 2us per step when optimize "s"
|
|
#endif
|
|
/*
|
|
* Branch to bootloader or application code ?
|
|
*/
|
|
|
|
#ifdef DUALSERIAL
|
|
selectedSerial = 0;
|
|
#endif //DUALSERIAL
|
|
|
|
|
|
#ifndef REMOVE_BOOTLOADER_LED
|
|
/* PROG_PIN pulled low, indicate with LED that bootloader is active */
|
|
PROGLED_DDR |= (1<<PROGLED_PIN);
|
|
// PROGLED_PORT &= ~(1<<PROGLED_PIN); // active low LED ON
|
|
PROGLED_PORT |= (1<<PROGLED_PIN); // active high LED ON
|
|
|
|
|
|
#endif
|
|
/*
|
|
* Init UART
|
|
* set baudrate and enable USART receiver and transmiter without interrupts
|
|
*/
|
|
#if UART_BAUDRATE_DOUBLE_SPEED
|
|
UART_STATUS_REG |= (1 <<UART_DOUBLE_SPEED);
|
|
#endif
|
|
UART_BAUD_RATE_LOW = UART_BAUD_SELECT(BAUDRATE,F_CPU);
|
|
UART_CONTROL_REG = (1 << UART_ENABLE_RECEIVER) | (1 << UART_ENABLE_TRANSMITTER);
|
|
|
|
asm volatile ("nop"); // wait until port has changed
|
|
|
|
#ifdef EINSYBOARD
|
|
pinsToDefaultState();
|
|
blinkBootLed(1);
|
|
#endif //EINSYBOARD
|
|
|
|
#ifdef DUALSERIAL
|
|
initUart();
|
|
#endif //DUALSERIAL
|
|
|
|
#ifdef LCD_HD44780
|
|
lcd_init();
|
|
lcd_clrscr();
|
|
lcd_goto(0);
|
|
/* if (boot_app_magic == 0x55aa55aa)
|
|
{
|
|
lcd_print_hex_dword(boot_src_addr);
|
|
lcd_putc(' ');
|
|
lcd_print_hex_dword(boot_dst_addr);
|
|
lcd_goto(42);
|
|
lcd_print_hex_word(boot_copy_size);
|
|
lcd_putc(' ');
|
|
lcd_print_hex_word(boot_app_flags);
|
|
lcd_putc(' ');
|
|
lcd_print_hex_dword(boot_app_magic);
|
|
boot_app_magic = 0x00000000;
|
|
while(1);
|
|
}*/
|
|
/* lcd_puts("B");
|
|
lcd_goto(21);
|
|
lcd_puts("Original Prusa i3");
|
|
lcd_goto(47);
|
|
lcd_puts("Prusa Research");*/
|
|
lcd_goto(65);
|
|
lcd_puts("Original Prusa i3");
|
|
lcd_goto(23);
|
|
lcd_puts("Prusa Research");
|
|
// lcd_goto(90);
|
|
// lcd_puts("boot... ...");
|
|
lcd_goto(101);
|
|
lcd_puts("...");
|
|
|
|
#endif //LCD_HD44780
|
|
|
|
|
|
#ifdef EINSYBOARD
|
|
blinkBootLed(0);
|
|
#endif //EINSYBOARD
|
|
|
|
uint16_t animationTimer = 0;
|
|
uint16_t animationFrame = 0;
|
|
|
|
|
|
while (boot_state==0)
|
|
{
|
|
#ifdef DUALSERIAL
|
|
while ((!(Serial_Available(0))) && (!(Serial_Available(2))) && (boot_state == 0)) // wait for data
|
|
{
|
|
_delay_ms(0.001);
|
|
boot_timer++;
|
|
if (boot_timer > boot_timeout)
|
|
{
|
|
boot_state = 1; // (after ++ -> boot_state=2 bootloader timeout, jump to main 0x00000 )
|
|
}
|
|
#ifdef BLINK_LED_WHILE_WAITING
|
|
if ((boot_timer % _BLINK_LOOP_COUNT_) == 0)
|
|
{
|
|
//* toggle the LED
|
|
PROGLED_PORT ^= (1<<PROGLED_PIN); // turn LED ON
|
|
}
|
|
#endif
|
|
}
|
|
if (Serial_Available(2))
|
|
selectedSerial = 2;
|
|
#else //DUALSERIAL
|
|
while ((!(Serial_Available())) && (boot_state == 0)) // wait for data
|
|
{
|
|
_delay_ms(0.001);
|
|
boot_timer++;
|
|
if (boot_timer > boot_timeout)
|
|
{
|
|
boot_state = 1; // (after ++ -> boot_state=2 bootloader timeout, jump to main 0x00000 )
|
|
}
|
|
#ifdef BLINK_LED_WHILE_WAITING
|
|
if ((boot_timer % _BLINK_LOOP_COUNT_) == 0)
|
|
{
|
|
//* toggle the LED
|
|
PROGLED_PORT ^= (1<<PROGLED_PIN); // turn LED ON
|
|
}
|
|
#endif
|
|
}
|
|
#endif //DUALSERIAL
|
|
boot_state++; // ( if boot_state=1 bootloader received byte from UART, enter bootloader mode)
|
|
}
|
|
|
|
int messageShown = 0;
|
|
|
|
if (boot_state==1)
|
|
{
|
|
//* main loop
|
|
while (!isLeave)
|
|
{
|
|
/*
|
|
* Collect received bytes to a complete message
|
|
*/
|
|
msgParseState = ST_START;
|
|
while ( msgParseState != ST_PROCESS )
|
|
{
|
|
if (boot_state==1)
|
|
{
|
|
boot_state = 0;
|
|
c = UART_DATA_REG;
|
|
}
|
|
else
|
|
{
|
|
// c = recchar();
|
|
c = recchar_timeout();
|
|
|
|
}
|
|
|
|
|
|
switch (msgParseState)
|
|
{
|
|
case ST_START:
|
|
if ( c == MESSAGE_START )
|
|
{
|
|
msgParseState = ST_GET_SEQ_NUM;
|
|
checksum = MESSAGE_START^0;
|
|
}
|
|
break;
|
|
|
|
case ST_GET_SEQ_NUM:
|
|
#ifdef _FIX_ISSUE_505_
|
|
seqNum = c;
|
|
msgParseState = ST_MSG_SIZE_1;
|
|
checksum ^= c;
|
|
#else
|
|
if ( (c == 1) || (c == seqNum) )
|
|
{
|
|
seqNum = c;
|
|
msgParseState = ST_MSG_SIZE_1;
|
|
checksum ^= c;
|
|
}
|
|
else
|
|
{
|
|
msgParseState = ST_START;
|
|
}
|
|
#endif
|
|
break;
|
|
|
|
case ST_MSG_SIZE_1:
|
|
msgLength = c<<8;
|
|
msgParseState = ST_MSG_SIZE_2;
|
|
checksum ^= c;
|
|
break;
|
|
|
|
case ST_MSG_SIZE_2:
|
|
msgLength |= c;
|
|
msgParseState = ST_GET_TOKEN;
|
|
checksum ^= c;
|
|
break;
|
|
|
|
case ST_GET_TOKEN:
|
|
if ( c == TOKEN )
|
|
{
|
|
msgParseState = ST_GET_DATA;
|
|
checksum ^= c;
|
|
ii = 0;
|
|
}
|
|
else
|
|
{
|
|
msgParseState = ST_START;
|
|
}
|
|
break;
|
|
|
|
case ST_GET_DATA:
|
|
msgBuffer[ii++] = c;
|
|
checksum ^= c;
|
|
if (ii == msgLength )
|
|
{
|
|
msgParseState = ST_GET_CHECK;
|
|
}
|
|
break;
|
|
|
|
case ST_GET_CHECK:
|
|
if ( c == checksum )
|
|
{
|
|
msgParseState = ST_PROCESS;
|
|
}
|
|
else
|
|
{
|
|
msgParseState = ST_START;
|
|
}
|
|
break;
|
|
} // switch
|
|
} // while(msgParseState)
|
|
|
|
#ifdef LCD_HD44780
|
|
if (messageShown == 0)
|
|
{
|
|
lcd_clrscr();
|
|
lcd_goto(20);
|
|
lcd_puts(" Do not disconnect!");
|
|
lcd_goto(45);
|
|
lcd_puts(" Upgrading firmware");
|
|
messageShown = 1;
|
|
}
|
|
#endif //LCD_HD44780
|
|
|
|
#ifdef LCD_HD44780_ANIMATION
|
|
if (flashSize == 0)
|
|
{
|
|
animationTimer++;
|
|
if (animationTimer > 10)
|
|
{
|
|
animationTimer = 0;
|
|
animationFrame++;
|
|
if (animationFrame > 5) animationFrame = 0;
|
|
lcd_goto(91);
|
|
lcd_puts("| |");
|
|
lcd_goto((animationFrame <= 3)?(92 + animationFrame):(98 - animationFrame));
|
|
lcd_putc('*');
|
|
}
|
|
}
|
|
#endif //LCD_HD44780_ANIMATION
|
|
|
|
#ifdef LCD_HD44780_COUNTER
|
|
if ((flashSize != 0) && flashOperation)
|
|
{
|
|
if (flashOperation == 1) //write
|
|
{
|
|
lcd_goto(88);
|
|
lcd_puts("write ");
|
|
}
|
|
if (flashOperation == 2) //verify
|
|
{
|
|
lcd_goto(87);
|
|
lcd_puts("verify ");
|
|
}
|
|
int progress = 100 * flashCounter / flashSize;
|
|
char text[4] = " ";
|
|
for (int i = 2; i >= 0; i--)
|
|
if (progress > 0)
|
|
{
|
|
text[i] = '0' + (progress % 10);
|
|
progress /= 10;
|
|
}
|
|
else
|
|
text[i] = ' ';
|
|
lcd_puts(text);
|
|
lcd_putc('%');
|
|
}
|
|
#endif //LCD_HD44780_COUNTER
|
|
|
|
/*
|
|
* Now process the STK500 commands, see Atmel Appnote AVR068
|
|
*/
|
|
|
|
switch (msgBuffer[0])
|
|
{
|
|
#ifndef REMOVE_CMD_SPI_MULTI
|
|
case CMD_SPI_MULTI:
|
|
{
|
|
unsigned char answerByte;
|
|
unsigned char flag=0;
|
|
|
|
if ( msgBuffer[4]== 0x30 )
|
|
{
|
|
unsigned char signatureIndex = msgBuffer[6];
|
|
|
|
if ( signatureIndex == 0 )
|
|
{
|
|
answerByte = (SIGNATURE_BYTES >> 16) & 0x000000FF;
|
|
}
|
|
else if ( signatureIndex == 1 )
|
|
{
|
|
answerByte = (SIGNATURE_BYTES >> 8) & 0x000000FF;
|
|
}
|
|
else
|
|
{
|
|
answerByte = SIGNATURE_BYTES & 0x000000FF;
|
|
}
|
|
}
|
|
else if ( msgBuffer[4] & 0x50 )
|
|
{
|
|
//* Issue 544: stk500v2 bootloader doesn't support reading fuses
|
|
//* I cant find the docs that say what these are supposed to be but this was figured out by trial and error
|
|
// answerByte = boot_lock_fuse_bits_get(GET_LOW_FUSE_BITS);
|
|
// answerByte = boot_lock_fuse_bits_get(GET_HIGH_FUSE_BITS);
|
|
// answerByte = boot_lock_fuse_bits_get(GET_EXTENDED_FUSE_BITS);
|
|
if (msgBuffer[4] == 0x50)
|
|
{
|
|
answerByte = boot_lock_fuse_bits_get(GET_LOW_FUSE_BITS);
|
|
}
|
|
else if (msgBuffer[4] == 0x58)
|
|
{
|
|
answerByte = boot_lock_fuse_bits_get(GET_HIGH_FUSE_BITS);
|
|
}
|
|
else
|
|
{
|
|
answerByte = 0;
|
|
}
|
|
}
|
|
else
|
|
{
|
|
answerByte = 0; // for all others command are not implemented, return dummy value for AVRDUDE happy <Worapoht>
|
|
}
|
|
if ( !flag )
|
|
{
|
|
msgLength = 7;
|
|
msgBuffer[1] = STATUS_CMD_OK;
|
|
msgBuffer[2] = 0;
|
|
msgBuffer[3] = msgBuffer[4];
|
|
msgBuffer[4] = 0;
|
|
msgBuffer[5] = answerByte;
|
|
msgBuffer[6] = STATUS_CMD_OK;
|
|
}
|
|
}
|
|
break;
|
|
#endif
|
|
case CMD_SIGN_ON:
|
|
msgLength = 11;
|
|
msgBuffer[1] = STATUS_CMD_OK;
|
|
msgBuffer[2] = 8;
|
|
msgBuffer[3] = 'A';
|
|
msgBuffer[4] = 'V';
|
|
msgBuffer[5] = 'R';
|
|
msgBuffer[6] = 'I';
|
|
msgBuffer[7] = 'S';
|
|
msgBuffer[8] = 'P';
|
|
msgBuffer[9] = '_';
|
|
msgBuffer[10] = '2';
|
|
break;
|
|
|
|
case CMD_GET_PARAMETER:
|
|
{
|
|
unsigned char value;
|
|
|
|
switch(msgBuffer[1])
|
|
{
|
|
case PARAM_BUILD_NUMBER_LOW:
|
|
value = CONFIG_PARAM_BUILD_NUMBER_LOW;
|
|
break;
|
|
case PARAM_BUILD_NUMBER_HIGH:
|
|
value = CONFIG_PARAM_BUILD_NUMBER_HIGH;
|
|
break;
|
|
case PARAM_HW_VER:
|
|
value = CONFIG_PARAM_HW_VER;
|
|
break;
|
|
case PARAM_SW_MAJOR:
|
|
value = CONFIG_PARAM_SW_MAJOR;
|
|
break;
|
|
case PARAM_SW_MINOR:
|
|
value = CONFIG_PARAM_SW_MINOR;
|
|
break;
|
|
default:
|
|
value = 0;
|
|
break;
|
|
}
|
|
msgLength = 3;
|
|
msgBuffer[1] = STATUS_CMD_OK;
|
|
msgBuffer[2] = value;
|
|
}
|
|
break;
|
|
|
|
case CMD_LEAVE_PROGMODE_ISP:
|
|
isLeave = 1;
|
|
//* fall thru
|
|
|
|
case CMD_SET_PARAMETER:
|
|
case CMD_ENTER_PROGMODE_ISP:
|
|
msgLength = 2;
|
|
msgBuffer[1] = STATUS_CMD_OK;
|
|
break;
|
|
|
|
case CMD_READ_SIGNATURE_ISP:
|
|
{
|
|
unsigned char signatureIndex = msgBuffer[4];
|
|
unsigned char signature;
|
|
|
|
if ( signatureIndex == 0 )
|
|
signature = (SIGNATURE_BYTES >>16) & 0x000000FF;
|
|
else if ( signatureIndex == 1 )
|
|
signature = (SIGNATURE_BYTES >> 8) & 0x000000FF;
|
|
else
|
|
signature = SIGNATURE_BYTES & 0x000000FF;
|
|
|
|
msgLength = 4;
|
|
msgBuffer[1] = STATUS_CMD_OK;
|
|
msgBuffer[2] = signature;
|
|
msgBuffer[3] = STATUS_CMD_OK;
|
|
}
|
|
break;
|
|
|
|
case CMD_READ_LOCK_ISP:
|
|
msgLength = 4;
|
|
msgBuffer[1] = STATUS_CMD_OK;
|
|
msgBuffer[2] = boot_lock_fuse_bits_get( GET_LOCK_BITS );
|
|
msgBuffer[3] = STATUS_CMD_OK;
|
|
break;
|
|
|
|
case CMD_READ_FUSE_ISP:
|
|
{
|
|
unsigned char fuseBits;
|
|
|
|
if ( msgBuffer[2] == 0x50 )
|
|
{
|
|
if ( msgBuffer[3] == 0x08 )
|
|
fuseBits = boot_lock_fuse_bits_get( GET_EXTENDED_FUSE_BITS );
|
|
else
|
|
fuseBits = boot_lock_fuse_bits_get( GET_LOW_FUSE_BITS );
|
|
}
|
|
else
|
|
{
|
|
fuseBits = boot_lock_fuse_bits_get( GET_HIGH_FUSE_BITS );
|
|
}
|
|
msgLength = 4;
|
|
msgBuffer[1] = STATUS_CMD_OK;
|
|
msgBuffer[2] = fuseBits;
|
|
msgBuffer[3] = STATUS_CMD_OK;
|
|
}
|
|
break;
|
|
|
|
#ifndef REMOVE_PROGRAM_LOCK_BIT_SUPPORT
|
|
case CMD_PROGRAM_LOCK_ISP:
|
|
{
|
|
unsigned char lockBits = msgBuffer[4];
|
|
|
|
lockBits = (~lockBits) & 0x3C; // mask BLBxx bits
|
|
boot_lock_bits_set(lockBits); // and program it
|
|
boot_spm_busy_wait();
|
|
|
|
msgLength = 3;
|
|
msgBuffer[1] = STATUS_CMD_OK;
|
|
msgBuffer[2] = STATUS_CMD_OK;
|
|
}
|
|
break;
|
|
#endif
|
|
case CMD_CHIP_ERASE_ISP:
|
|
eraseAddress = 0;
|
|
msgLength = 2;
|
|
// msgBuffer[1] = STATUS_CMD_OK;
|
|
msgBuffer[1] = STATUS_CMD_FAILED; //* isue 543, return FAILED instead of OK
|
|
break;
|
|
|
|
case CMD_LOAD_ADDRESS:
|
|
#if defined(RAMPZ)
|
|
address = ( ((address_t)(msgBuffer[1])<<24)|((address_t)(msgBuffer[2])<<16)|((address_t)(msgBuffer[3])<<8)|(msgBuffer[4]) )<<1;
|
|
#else
|
|
address = ( ((msgBuffer[3])<<8)|(msgBuffer[4]) )<<1; //convert word to byte address
|
|
#endif
|
|
msgLength = 2;
|
|
msgBuffer[1] = STATUS_CMD_OK;
|
|
break;
|
|
|
|
case CMD_SET_UPLOAD_SIZE_PRUSA3D:
|
|
((unsigned char*)&flashSize)[0] = msgBuffer[1];
|
|
((unsigned char*)&flashSize)[1] = msgBuffer[2];
|
|
((unsigned char*)&flashSize)[2] = msgBuffer[3];
|
|
((unsigned char*)&flashSize)[3] = 0;
|
|
msgLength = 2;
|
|
msgBuffer[1] = STATUS_CMD_OK;
|
|
break;
|
|
|
|
case CMD_PROGRAM_FLASH_ISP:
|
|
case CMD_PROGRAM_EEPROM_ISP:
|
|
{
|
|
unsigned int size = ((msgBuffer[1])<<8) | msgBuffer[2];
|
|
unsigned char *p = msgBuffer+10;
|
|
unsigned int data;
|
|
unsigned char highByte, lowByte;
|
|
address_t tempaddress = address;
|
|
|
|
|
|
if ( msgBuffer[0] == CMD_PROGRAM_FLASH_ISP )
|
|
{
|
|
if (flashSize != 0)
|
|
{
|
|
if (address == 0) //first page
|
|
{
|
|
flashCounter = size; //initial value = size
|
|
flashAddressLast = 0; //last
|
|
flashOperation = 1; //write
|
|
}
|
|
else if (address != flashAddressLast)
|
|
flashCounter += size; //add size to counter
|
|
flashAddressLast = address;
|
|
}
|
|
|
|
// erase only main section (bootloader protection)
|
|
if (eraseAddress < APP_END ) //erase and write only blocks with address less 0x3e000
|
|
{ //because prevent "brick"
|
|
boot_page_erase(eraseAddress); // Perform page erase
|
|
boot_spm_busy_wait(); // Wait until the memory is erased.
|
|
eraseAddress += SPM_PAGESIZE; // point to next page to be erase
|
|
}
|
|
if (address < APP_END)
|
|
{
|
|
/* Write FLASH */
|
|
do {
|
|
lowByte = *p++;
|
|
highByte = *p++;
|
|
|
|
data = (highByte << 8) | lowByte;
|
|
boot_page_fill(address,data);
|
|
|
|
address = address + 2; // Select next word in memory
|
|
size -= 2; // Reduce number of bytes to write by two
|
|
} while (size); // Loop until all bytes written
|
|
|
|
boot_page_write(tempaddress);
|
|
boot_spm_busy_wait();
|
|
boot_rww_enable(); // Re-enable the RWW section
|
|
}
|
|
}
|
|
else
|
|
{
|
|
//* issue 543, this should work, It has not been tested.
|
|
uint16_t ii = address >> 1;
|
|
/* write EEPROM */
|
|
while (size) {
|
|
eeprom_write_byte((uint8_t*)ii, *p++);
|
|
address+=2; // Select next EEPROM byte
|
|
ii++;
|
|
size--;
|
|
}
|
|
}
|
|
msgLength = 2;
|
|
msgBuffer[1] = STATUS_CMD_OK;
|
|
|
|
}
|
|
break;
|
|
|
|
case CMD_READ_FLASH_ISP:
|
|
case CMD_READ_EEPROM_ISP:
|
|
{
|
|
unsigned int size = ((msgBuffer[1])<<8) | msgBuffer[2];
|
|
unsigned char *p = msgBuffer+1;
|
|
msgLength = size+3;
|
|
|
|
*p++ = STATUS_CMD_OK;
|
|
if (msgBuffer[0] == CMD_READ_FLASH_ISP )
|
|
{
|
|
if (flashSize != 0)
|
|
{
|
|
if ((address == 0x00000) && (flashOperation == 1))
|
|
{
|
|
flashOperation = 2; //verify
|
|
flashCounter = size; //initial value = size
|
|
}
|
|
else
|
|
flashCounter += size; //add size to counter
|
|
}
|
|
|
|
unsigned int data;
|
|
|
|
// Read FLASH
|
|
do {
|
|
//#if defined(RAMPZ)
|
|
#if (FLASHEND > 0x10000)
|
|
data = pgm_read_word_far(address);
|
|
#else
|
|
data = pgm_read_word_near(address);
|
|
#endif
|
|
*p++ = (unsigned char)data; //LSB
|
|
*p++ = (unsigned char)(data >> 8); //MSB
|
|
address += 2; // Select next word in memory
|
|
size -= 2;
|
|
}while (size);
|
|
}
|
|
else
|
|
{
|
|
/* Read EEPROM */
|
|
do {
|
|
EEARL = address; // Setup EEPROM address
|
|
EEARH = ((address >> 8));
|
|
address++; // Select next EEPROM byte
|
|
EECR |= (1<<EERE); // Read EEPROM
|
|
*p++ = EEDR; // Send EEPROM data
|
|
size--;
|
|
} while (size);
|
|
}
|
|
*p++ = STATUS_CMD_OK;
|
|
}
|
|
break;
|
|
|
|
default:
|
|
msgLength = 2;
|
|
msgBuffer[1] = STATUS_CMD_FAILED;
|
|
break;
|
|
}
|
|
|
|
/*
|
|
* Now send answer message back
|
|
*/
|
|
sendchar(MESSAGE_START);
|
|
checksum = MESSAGE_START^0;
|
|
|
|
sendchar(seqNum);
|
|
checksum ^= seqNum;
|
|
|
|
c = ((msgLength>>8)&0xFF);
|
|
sendchar(c);
|
|
checksum ^= c;
|
|
|
|
c = msgLength&0x00FF;
|
|
sendchar(c);
|
|
checksum ^= c;
|
|
|
|
sendchar(TOKEN);
|
|
checksum ^= TOKEN;
|
|
|
|
p = msgBuffer;
|
|
while ( msgLength )
|
|
{
|
|
c = *p++;
|
|
sendchar(c);
|
|
checksum ^=c;
|
|
msgLength--;
|
|
}
|
|
sendchar(checksum);
|
|
seqNum++;
|
|
|
|
#ifndef REMOVE_BOOTLOADER_LED
|
|
//* <MLS> toggle the LED
|
|
PROGLED_PORT ^= (1<<PROGLED_PIN); // active high LED ON
|
|
#endif
|
|
|
|
}
|
|
}
|
|
|
|
|
|
|
|
|
|
#ifndef REMOVE_BOOTLOADER_LED
|
|
PROGLED_DDR &= ~(1<<PROGLED_PIN); // set to default
|
|
PROGLED_PORT &= ~(1<<PROGLED_PIN); // active low LED OFF
|
|
// PROGLED_PORT |= (1<<PROGLED_PIN); // active high LED OFf
|
|
delay_ms(100); // delay after exit
|
|
#endif
|
|
|
|
exit:
|
|
asm volatile ("nop"); // wait until port has changed
|
|
|
|
/*
|
|
* Now leave bootloader
|
|
*/
|
|
|
|
UART_STATUS_REG &= 0xfd;
|
|
boot_rww_enable(); // enable application section
|
|
|
|
|
|
asm volatile(
|
|
"clr r30 \n\t"
|
|
"clr r31 \n\t"
|
|
"ijmp \n\t"
|
|
);
|
|
// asm volatile ( "push r1" "\n\t" // Jump to Reset vector in Application Section
|
|
// "push r1" "\n\t"
|
|
// "ret" "\n\t"
|
|
// ::);
|
|
|
|
/*
|
|
* Never return to stop GCC to generate exit return code
|
|
* Actually we will never reach this point, but the compiler doesn't
|
|
* understand this
|
|
*/
|
|
for(;;);
|
|
}
|
|
|
|
/*
|
|
base address = f800
|
|
|
|
avrdude: Device signature = 0x1e9703
|
|
avrdude: safemode: lfuse reads as FF
|
|
avrdude: safemode: hfuse reads as DA
|
|
avrdude: safemode: efuse reads as F5
|
|
avrdude>
|
|
|
|
|
|
base address = f000
|
|
avrdude: Device signature = 0x1e9703
|
|
avrdude: safemode: lfuse reads as FF
|
|
avrdude: safemode: hfuse reads as D8
|
|
avrdude: safemode: efuse reads as F5
|
|
avrdude>
|
|
*/
|
|
|
|
//************************************************************************
|